Erinevus lehekülje "LACP kasutamine" redaktsioonide vahel
Allikas: Kuutõrvaja
(→FreeBSD) |
(→OpenBSD) |
||
| 89. rida: | 89. rida: | ||
===OpenBSD=== | ===OpenBSD=== | ||
| − | + | LACP seadme moodustamiseks sobib öelda nt | |
| + | |||
| + | # ifconfig trunk0 trunkport re1 trunkport re2 trunkproto lacp | ||
| + | |||
| + | Seadme omaduste esitamiseks | ||
| + | |||
| + | # ifconfig trunk0 | ||
| + | trunk0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 | ||
| + | lladdr 00:0c:42:07:1a:45 | ||
| + | priority: 0 | ||
| + | trunk: trunkproto lacp | ||
| + | trunk id: [(8000,00:0c:42:07:1a:45,40E4,0000,0000), | ||
| + | (8000,a8:b1:d4:95:a3:85,0003,0000,0000)] | ||
| + | trunkport re2 active,collecting,distributing | ||
| + | trunkport re1 active,collecting,distributing | ||
| + | groups: trunk | ||
| + | media: Ethernet autoselect | ||
| + | status: active | ||
| + | inet6 fe80::20c:42ff:fe07:1a45%trunk0 prefixlen 64 scopeid 0x1c | ||
| + | inet 192.168.0.1 netmask 0xffffff00 broadcast 192.168.0.255 | ||
| + | |||
| + | kus | ||
| + | |||
| + | * trunk id järel on esitatud komponentide mac aadressid | ||
===FreeBSD=== | ===FreeBSD=== | ||
Redaktsioon: 1. august 2010, kell 21:24
Sisukord
Sissejuhatus
Ethernet interface bonding tehnika võimaldab teatud tingimustel kasutada mitut arvutisse paigaldatud füüsilist võrguseadet ühe loogilise seadmena.
Tööpõhimõte
TODO
SLM2008 lüliti
TODO
Debian GNU/Linux
Tarkvara paigaldamine
Vajalik tarkvara sisaldub operatsioonisüsteemi tuumas, juhtprogrammi ifenslave paigaldamiseks sobib öelda
# apt-get install ifenslave-2.6
Seadistamine
Bonding seadme nimeks on tavaliselt bond0 ning nt failover bonding seade seadistatakse /etc/network/interfaces sektsiooniga
auto bond0 iface bond0 inet static address 10.0.3.87 netmask 255.255.255.0 slaves eth1 eth2 bond_mode active-backup bond_miimon 100
Vastav seadistamine käsurealt võiks toimuda nt selliselt
# modprobe bonding mode=802.3ad lacp_rate=1 miimon=100 xmit_hash_policy=layer3+4 # ifconfig bond0 10.0.3.87 netmask 255.255.0.0 # ifenslave bond0 eth1 eth2
Bonding seadme eemaldamiseks sobib öelda
# ifenslave -d bond0 eth1 eth2 # rmmod bonding
Bonding seadme omadusi saab vaadata
# cat /proc/net/bonding/bond0
Ethernet Channel Bonding Driver: v3.2.5 (March 21, 2008)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer3+4 (1)
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
802.3ad info
LACP rate: fast
Active Aggregator Info:
Aggregator ID: 1
Number of ports: 2
Actor Key: 17
Partner Key: 3
Partner Mac Address: a8:b1:d4:95:a3:85
Slave Interface: eth1
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:0e:0c:ba:4b:3e
Aggregator ID: 1
Slave Interface: eth2
MII Status: up
Link Failure Count: 4
Permanent HW addr: 00:1b:21:1d:f6:06
Aggregator ID: 1
kus
- Bonding Mode: IEEE 802.3ad Dynamic link aggregation - kasutusel olev bonding režiim
Kasutamine
TODO
OpenBSD
LACP seadme moodustamiseks sobib öelda nt
# ifconfig trunk0 trunkport re1 trunkport re2 trunkproto lacp
Seadme omaduste esitamiseks
# ifconfig trunk0
trunk0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:0c:42:07:1a:45
priority: 0
trunk: trunkproto lacp
trunk id: [(8000,00:0c:42:07:1a:45,40E4,0000,0000),
(8000,a8:b1:d4:95:a3:85,0003,0000,0000)]
trunkport re2 active,collecting,distributing
trunkport re1 active,collecting,distributing
groups: trunk
media: Ethernet autoselect
status: active
inet6 fe80::20c:42ff:fe07:1a45%trunk0 prefixlen 64 scopeid 0x1c
inet 192.168.0.1 netmask 0xffffff00 broadcast 192.168.0.255
kus
- trunk id järel on esitatud komponentide mac aadressid
FreeBSD
TODO
- Ametlik FreeBSD manual http://www.freebsd.org/doc/handbook/network-aggregation.html
